Home / Higg Index Tools / Higg FEM / FEM Glossary

FEM Glossary

1. Words A-D

Absolute reductions

Reduction in actual utility consumption (e.g. kWh of electricity used, or cubic meter of water used for the whole facility within a calendar year) or pollution generated (e.g. kg of hazardous waste for the whole facility within a calendar year) regardless of facility size, production volumes, production hours, raw material usage or other business metrics

Source: Higg Index

Air emission inventory

An inventory of emissions to air is a detailed list of the emissions and their sources, it should include the following information for each emission source: • The pollutants known or likely to be present • The quantity emitted (if known or estimated) • The location of, for example, the stack, vent etc • Any control devices (e.g. abatement equipment) installed • Frequency of monitoring; and • Whether the particular emission is legally regulated.

Source: Higg Index

Air pollution control

Air pollution control refer to steps taken to maintain a standard of purity of air for good public health; for protection of plant and animal life, and property; for visibility; and for safe ground and air transportation.

Source: OECD

All waste stream

All waste stream means all the wastes produced on-site including wastes generated from manufacturing the product, office use, waste produced by workers at the canteen, dormitory, and waste produced by contractors coming on-site to perform a service.

Source: Higg Index

Alternative assessment

It is a process for identifying alternatives (chemical or non-chemical) to a chemical of concern, screening out equally or more hazardous alternatives, and selecting an alternative that is technically and economically viable and does not have the potential for causing significant environmental or human health impacts.

Source: OIA – Chemicals Management Framework Glossary

Barriers

Any coatings and/or laminations used on textiles or footwear products. Barriers may be bicomponent (two or more materials), microporous (material with pore diameters of less than 2nm) or monolithic (single covering without seams or joints).

Source: Higg Index

Baseline

Baseline is the initial metric for the utility used to be improved from. The initial metric is the beginning measure taken to establish a stable starting point to evaluate improvement against. It must reference a specific time frame from which the baseline was calculated, typically annual consumption. Identifying any unique variables makes the metric more accurate.

Source: Higg Index

Best Available Technology (BAT)

In the FEM, the concept of Best Available Technology (BAT) is defined as the most effective and advanced technology including materials, processes, and equipment that is currently available that will result in reduction of pollutants emitted and minimizing impacts to the environment.

Source: Higg Index

Biological oxygen demand (BOD)

Biological Oxygen Demand (or Biochemical Oxygen Demand) (BOD) is an indicator of the level of organic matter in the water and, hence, the rate at which oxygen in the water is used up as the organic matter is consumed by organisms in the water. Generally, the lower the BOD, the better the water/ wastewater quality.

Source: Higg Index & GSCP

Biomass

Biomass is biological material from living or recently living organisms. Sustainable biomass sources are:

Energy crops that do not compete with food crops for land; high yield crops grown specifically for energy applications.
Agricultural residues: residues from agriculture harvesting or processing, such as wheat straw or rice husk.
Sustainably-harvested wood and forest residues.
Waste wood

Source: Higg Index

Biomass- Without sustainably sourced biomass certification

Any biomass that is not certified through a sustainably sourced biomass program.

Source: Higg Index

Biomass- Sustainably sourced with certifications

Any biomass that has supporting certification documentation from a sustainably sourced biomass program (e.g., Forest Stewardship Council (FSC), Programme for the Endorsement of Forest Certification (PEFC), ISCC Biomass Certification, Sustainable Biomass Program (SBP) Certification, Better Biomass Certification, Country Specific Certification, etc.)

Source: Higg Index

Black Water

Black water is defined in the FEM as wastewater from toilets which can contain pathogens, feces, urine, and other sanitary waste from flushed toilets.

Source: Higg Index

Blue Water

Blue water is fresh surface and groundwater, in other words, the water in freshwater lakes, rivers and aquifers. Blue water sources are : Surface Water ,Groundwater, Municipal Blue, Water, Municipal Water (Origin Unknown), Brackish surface water/seawater, Condensate from External Steam Source, Rainwater

Source: Higg Index

Brackish surface water/seawater

Brackish water is water in which the concentration of salts is relatively high (over 10,000 mg/l). Seawater has a typical concentration of salts above 35,000 mg/l.

Source: CDP Water Reporting Guidance

Carbon offsets

Carbon offsets are market-based instruments that are designed to lower the amount of GHG in the atmosphere (mainly CO2). Offsets provide credits that can be purchased and applied to reduce an organization’s carbon footprint by accounting for CO2 emission reductions that occur elsewhere. Carbon offsets fund specific projects that either lower CO2 emissions, or sequester CO2, meaning they take some CO2 out of the atmosphere and store it. Common examples of projects include reforestation, construction of renewable energy infrastructure, carbon-storing agricultural practices, and waste and landfill management.

Source: Higg Index

CAS number

CAS Registry Numbers (often referred to as CAS RN® or CAS Numbers) are universally used to provide a unique, unmistakable identifier for chemical substances. A CAS Registry Number itself has no inherent chemical significance but provides an unambiguous way to identify a chemical substance or molecular structure when there are many possible systematic, generic, proprietary or trivial names.

Source: CAS

Chemical oxygen demand (COD)

Chemical Oxygen Demand (COD) is an indicator of the level of organic matter and chemicals in the water and, hence, the rate at which oxygen in the water is used up as the organic matter and chemicals are consumed. Generally, the lower the COD the better the water/ wastewater quality.

Source: GSCP

Circular economy

A circular economy is an alternative to a traditional linear economy (make, use, dispose) in which we keep resources in use for as long as possible, extract the maximum value from them whilst in use, then recover and regenerate products and materials at the end of each service life.

Source: WRAP

Climate change

Climate change refers to any long-term change in Earth’s climate, or in the climate of a region or city. This includes warming, cooling and changes besides temperature.

Source: NASA

Coal

commercial mix includes all types of traditional coal (e.g., anthracite, bituminous, etc.)

Coal Water Slurry

Coal Water Slurry is a combustible mixture of fine coal particles suspended in water used as fuel source.

Commodity Chemical

Single substances or chemical compounds whose chemical structure is well-known, and their use is to create conditions for a process (such as acid, alkaline, oxidizing, reducing, solubilizing conditions). They are produced in high volumes with low prices and do not have a brand name but are known by their common chemical names (for example, Acetic Acid). The chemical structure and purity of two commodity chemicals produced by different manufacturers can be the same and can be interchangeable. They are generally sold on technical specifications (such as purity) and are not designed for a unique/special property or effect nor require any scientific research in their development. Usually, commodity chemicals either get reacted in the process (for example Sodium Hydroxide or Sodium Hydrosulphite) or remain in the effluent after the process (for example Common Salt or Glauber’s Salt used in reactive dyeing of cotton)

Source: ZDHC Performance Incheck Guidelines

Condensate from external steam source

Water that is generated from the condensate of steam sources that are not located at the facility.

Domestic Energy use

Energy that is consumed in non-production related areas and/or buildings such as employee washrooms, domestic only wastewater treatment plant, or office areas separated from production, canteen and kitchen, security posts, external lighting (e.g. roadway or landscape lighting), medical center, etc.

Source: Higg Index

Domestic Wastewater

Wastewater originating from domestic/sanitary usage such as toilets, bathing, personal laundry and kitchens.

Source: Higg Index

Domestic water

Water used for washrooms, sanitation, food preparation, landscape irrigation, non-contact cooling etc.

Source: Higg Index

Downcycle waste

Pre or post-consumer wastes are recycled and processed to produce material or products of lesser economic value (e.g., recycled textiles used for rags, carpet padding, or sound insulation products).

Source: Higg Index

Downstream Scope 3 Emission Sources

1. Downstream transportation and distribution

2. Processing of sold products

3. Use of sold products

4. End-of-life treatment of sold products

5. Downstream leased assets

6. Franchises

7. Investments

Source: GHG protocol

2. Words E-H

Emergency Response Plan (ERP)

An Emergency Response Plan is a plan of action for the efficient deployment and coordination of services, agencies and personnel to provide the earliest possible response to an emergency.

Source: WREM

Emission from Facility Operations

For the Higg FEM, these include emissions from sources that support facility operations and are not the direct result of production processes. Emissions from facility operations are typically emitted through point source or mobile emissions sources. Examples include boilers, generators, heating and cooling systems (e.g., combustion heating, refrigerant-containing cooling equipment), and combustion engines.

Source: Higg Index

Emissions from Production:

For the Higg FEM, these include emissions from sources that are related to production processes. Emissions from production are typically emitted through point sources or as fugitive emissions. Examples include production processes that use chemicals (e.g., solvents, adhesives, printing, dyeing) processes that emit dust/particulates, products of combustion, or other hazardous or toxic air pollutants.

Source: Higg Index

Energy (indirect)

Energy (indirect) can be purchased from public and private utilities in the form of electricity, steam, or heat.

Source: Higg Index

Energy Attribute Certificates (EACs)

Energy Attribute Certificates (EACs) is a general term for a variety of market-based instruments that represent how energy is generated and ownership of the attributes of that energy. The name and specific requirements for EACs are typically defined by the jurisdiction or program under which they are issued. EACs can be issued as part of government initiatives or be offered by independent third-party providers such as the EAC programs

Source: Higg Index

Energy Audit

An energy audit is a systematic review of a facility’s energy use to identify areas of inefficiency and opportunities for improvement. An energy audit uses the principles of effective energy management systems and audit processes, such as ASHRAE Standard 211-2018, or ISO 50002 to help identify inefficiencies and define energy strategies for reducing energy consumption and operating costs.

Energy carrier

Substance or phenomenon that can be used to produce mechanical work or heat or to operate chemical or physical processes.

Source: ISO

Energy Recovery – Residual Management (e.g., Physical / Chemical / Biological Treatment)

Energy Recovery as a form of residual management, ie. Sludge Treatment that leads to Biogas Generation, heat generation from biological treatment (composting), energy generation from any such activity that does not include “Incineration”

Source: Higg Index

Energy Recovery (e.g., Incineration with energy recovery for Recyclables)

Energy recovery from the process of incinerating of recyclable waste. Note: Material recovery is the preferred method for recyclable wastes. Note: Recycling infrastructure and capabilities may differ among regions and countries.

Source: Higg Index

Environment Impact Assessment

An environmental impact assessment is a comprehensive review of all inputs and outputs of facility operations and production processes to identify potential impact areas, including impact areas like energy, water, waste, etc as well as other impact areas such as legal compliance, environmental noise and vibration

Source: Higg Index

Environmental Management System

A management system is a set of interrelated elements used to establish policy and objectives and to achieve those objectives. An environmental management system must consist of: a. Environmental Policy b. Planning: environmental risk assessment, setting objectives and targets c. Implementation and operation: operational procedures; adequate training; documentation and its control d. Checking: monitoring and measurement, audit and inspections e. Management Review

Source: GSCP, Higg Index based on ISO 14001:2004

Environmental policyThe policy describes the site’s activities, products, and services including a commitment to continual improvement and prevention of pollution, as well as a commitment to comply with legal and other requirements that relate to the significant environmental aspects identified for the site. The policy should set out the framework for setting and reviewing environmental objectives and targets.

Source: Higg Index

Final disposal

Final disposal means the final step to transform or destroy your waste. If your contractor is only collecting your waste and selling it to another company, the final disposal will be the last company that handles your waste by recycling or incinerating or treating (physical or chemical treatment) or landfilling your waste. This can be controlled in the factory by checking the waste collection area and confirming that sorting is well-managed.

Source: Higg Index

Foams

A solid “open cell” or “closed cell” foam material commonly used in packaging and footwear. Includes EVA, PE, and PU foam.

Fossil fuels

Fossil fuels are coal, oil and natural gas. They are derived from the remains of ancient plant and animal life.

Source: OECD

Fresh surface water

Surface water is naturally occurring water on the Earth’s surface in ice sheets, ice caps, glaciers, icebergs, bogs, ponds, lakes, rivers and streams. (Fresh water underground is called groundwater and oceans are not freshwater). Fresh water sources are generally characterized by having low concentrations of dissolved salts (below 1,000 mg/l) and other total dissolved solids.

Source: CDP Water Reporting Guidance

Freshwater

The most common freshwater use is potable municipal or city water (drinking water). Other sources can be from ground water wells, surface waters (lakes, rivers, and streams), rain water, and even condensate when collected from steam which is supplied to the business from an external source.

Source: Higg Index

Freshwater Footprint

Freshwater Footprint is defined as the total volume of all freshwater used to produce goods and services within a defined time period. This includes freshwater use in canteens, dormitories, landscape irrigation, vehicle washing, etc. – all freshwater use. The number represents the environmental impact as it pertains to freshwater use. A sustainable business should strive to minimize freshwater footprint. Many ways can be used to reduce freshwater use, including: fixing leaks, manufacturing process efficiency improvements, technology upgrades, reuse, and recycling

Source: Higg Index

Fuel Oil

Blended includes all types of fuel oils (e.g., furnace oil, bunker fuel, etc.)

Fugitive

Fugitive emissions are defined as those emissions which could not reasonably pass through a stack, chimney, vent, or other functionally-equivalent opening

Source: US EPA

Global Harmonization System (GHS)

GHS stands for the Globally Harmonized System of Classification and Labelling of Chemicals. GHS defines and classifies the hazards of chemical products and communicates health and safety information on labels and safety data sheets). The goal is that the same set of rules for classifying hazards, and the same format and content for labels and safety data sheets (SDS) will be adopted and used around the world. An international team of hazard communication experts developed GHS.

Source: CCOHS

Greenhouse gases emissions (GHG)

Gases that trap heat in the atmosphere are called greenhouse gases. The primary human activity affecting the amount and rate of climate change is greenhouse gas emissions from the burning of fossil fuels. The most common GHG, regulated under the Kyoto Protocol and are usually accounted in GHG inventories, are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), sulfur hexafluoride (SF6), hydrofluorocarbons (HFCs), perfluorocarbons (PFCs) and Nitrogen trifluoride (NF3). A site’s GHG emissions, sometimes called ‘carbon footprint,’ refer to the amount of GHG emitted to the atmosphere as a result of the site’s activities, whether from energy use, refrigerant use and wastewater treatment or other. The scope of measuring and tracking of a site’s GHG emissions is defined by different international accounting standards like the ISO14064, GHG Protocol – A Corporate and Accounting Standard (Revised Edition), etc. Local GHG accounting requirements and standards may be available.

Source: Adapted from US EPA and GHG Protocol

Grey Water

Grey water is water that has been polluted by human activity (e.g., industrial and/ or domestic sources). Grey water sources are: Municipal Grey Water, Recycled Water, Reuse Water, Treated Wastewater from External Source, Untreated Wastewater from External Sources (treated internally)

Groundwater

Water in soil beneath the soil surface, usually under conditions where the pressure in the water is greater than the atmospheric pressure, and the soil voids are substantially filled with the water. Non-renewable groundwater is generally located at deeper depths and cannot be replenished easily or is replenished over very long periods of time. They are sometimes referred to as “fossil” groundwater sources.

Source: CDP Water Reporting Guidance

Hazardous or Toxic Air Pollutants (HAP/TAP)

Hazardous or Toxic Air Pollutants (HAP/TAP) Are defined as compounds that are known or suspected to cause significant harmful impacts to human health or the environment.

Source: Higg Index

Hazardous waste

Hazardous waste is waste that could cause harm to public health and/or the environment because of its chemical, physical, or biological characteristics (e.g., it is flammable, explosive, toxic, radioactive, or infectious). The U.S. Environmental Protection Agency defines hazardous waste as “waste that is dangerous or potentially harmful to our health or the environment. Hazardous wastes can be liquids, solids, or gases, or sludge.

Source: US EPA

Higg FEM Trainer

An Individual qualified to provide Higg Index FEM Training.

Source: Higg FEM Training Program

3. Words I-L

Incinerated with energy recovery

Materials that are collected and intentionally allocated to incineration, gasification, anaerobic digestion, or other technology that recovers the inherent useful energy of the material. Methods that prevent environmental impacts and maximize resource utilization are required.

Source: Higg Index

Incineration

Materials that are collected and managed through an incineration process that meets international standards.

Source: Higg Index

Incineration with energy recovery for Non-Recyclables only

Energy recovery from the process of incinerating non-recyclable waste. Note: Recycling infrastructure and capabilities may differ among regions and countries.

Source: Higg Index

Industrial Wastewater

Water that has been used for manufacturing processes and no longer meets the quality standard for beneficial use (e.g., wastewater from production, lubrication, cooling, maintenance, cleaning of production machines, etc.)

Source: Higg Index

Insulation Materials

Substance used to reduce or prevent the transmission of heat, sound or electricity. Insulation materials can be natural (e.g. duck/goose down, or wool) or synthetic (e.g. polyester insulation).

Landfill

Materials that are collected and managed through a landfilling process that meets international standards.

Source: Higg Index

Landfill/Dumping with No Control Measures

In the Higg FEM, landfill/dumping with no controls aligns with the ZDHC Disposal Pathways definitions for landfills with limited or no control measures as defined in the ZDHC Sludge Management Document Version 1.0. As described below: Landfills with Limited Control Measures are landfill types that do not meet the description requirements specified in the Landfill with Significant Control Measures section. The permeability, leachate and gas control, and documentation are generally less restrictive. Leachate control may be non-existent or consist of simple collection and drain to local sewer lines. Gases may be vented versus stored, treated and used. Monitoring requirements for these types of landfills are less stringent – requiring less frequent sampling, inspections, and records for a shorter time depending on the local laws and regulations. Landfills with No Control Measures are landfills constructed with no control measures. Any landfill that has not been designed to contain waste, limit percolation, or control leachates from exposure or entering the environment is considered a landfill with no control measure. This includes dump piles and holes with no lining or packing to limit waste exposure to the ground and/or groundwater. There may be few or no monitoring requirements for these types of landfills. In many cases, these types of landfills are constructed by simply digging a hole and then filling the hole with waste, or it may consist of filling a naturally occurring depression with waste.

Source: Higg Index

Leachate

Leachate is the liquid (e.g.: rain) that drains or ‘leaches’ (e.g. water contained in food waste) from waste when water percolates through any waste. It varies widely in composition regarding the age of the waste and the type of waste. It usually contains both dissolved and suspended material.

Source: Higg Index

Life Cycle Assessment (LCA)

A life cycle assessment (LCA) is a systematic approach to evaluate the environmental footprint of a product. This evaluation goes beyond just assessing chemical hazards and risk and is a more comprehensive approach to sustainability which looks at the life cycle impacts within and beyond the facility. LCAs should be conducted by qualified individuals in accordance with a recognized LCA framework such as ISO14040:2006.

Location-based emission factors

Location-based emission factors use the average emission factor for the energy/emission source (e.g. regional or national emission factors)

Source: Higg Index

4. Words M-P

Manufacturing Restricted Substance Lists (MRSLs)

The ZDHC MRSL is a list of chemical substances subject to a usage ban (see Usage Ban, page 2). The MRSL applies to chemicals used in facilities that process materials and trim parts for use in apparel and footwear. Chemicals in the ZDHC MRSL include solvents, cleaners, adhesives, paints, inks, detergents, dyes, colorants, auxiliaries, coatings and finishing agents used during raw material production, wet-processing, maintenance, wastewater treatment, sanitation and pest control.

Source: ZDHC

Market-based emission factors

Market-based emission factors consider contractual arrangements under which the organization procures power from specific sources (e.g. fossil fuels, renewable). These emission factors are typically specified in Energy Attribute Certificates (EACs), contracts such as a power purchase agreement (PPA), to purchase electricity from a specified generating facility, or provided as Supplier-Specific Emission Factors.

Source: Higg Index

Material waste

These wastes may include scrap generated during the production or leftover / unused. Some example of material waste in Apparel, Textiles, and Footwear industry (not exhaustive) are:

Leather (synthetic or natural) • Glass • Fabric (Cotton or Nylon or blended)
Polyurethane Foams (laminated or unlaminated)
Lining materials
Rubber
EVA
Lining materials
Mixed material waste.

Source: Higg Index

Material Processes

Refer Definition Table below

Mobile Emissions Source

Mobile emission sources are those that are non-stationary sources of emission. Examples include powered motor vehicles (e.g., forklifts, trucks, passenger vehicles), heavy machinery (e.g., mobile cranes or lifts), small engines (e.g., landscaping equipment).

Source: Higg Index

Municipal Blue Water

Water provided by a municipality or other public provider that is generated by blue water.

Municipal Blue water (Origin unknown)

Water provided by a municipality or other public provider with unknown origin (e.g., blue, or grey water)

Municipal Grey Water

Water provided by a municipality or other public provider that is generated by grey water.

Municipal water

Water provided by a municipality or other public provider.

Source: CDP Water Reporting Guidance

Non-Hazardous wastes

Discarded materials from the consumption of goods and services and the manufacture of goods (e.g. cloth, leather, plastic, and paper or packaging waste. Non-hazardous waste usually includes non-hazardous production waste and domestic waste. Non-hazardous waste, such as food waste or plastic waste can still pose contamination and fire risks if not properly managed.

Source: Higg Index

Non-valorized disposal – Other Treatment

Any disposal method that does not recover usable materials or attributes of the waste such as converting them into more useful by products like raw materials, fuels, or other sources of energy.

Source: Higg Index

Non-valorized disposal – Responsibly Managed Landfills (for waste that cannot be managed in any of the options under Preferred options or Less Preferred Options)

In the Higg FEM, responsibly managed landfills aligns with the ZDHC Disposal Pathways definitions for landfills with significant control measures as defined in the ZDHC Sludge Management Document Version 1.0. available here: https://www.roadmaptozero.com/output, and as described below: Landfills with Significant Control Measures are landfills that control both leachate and gas produced from the materials placed in the landfill and are engineered to store waste in a manner that is safe to the surrounding environment. For purposes of the WW Guideline, significant control measures are defined as: Lined landfill such that the permeability of no more than 1 x 10-7 cm/sec is achieved. This is most often achieved using a synthetic composite liner on top of a packed natural clay liner but can also be achieved through two synthetic liners. Leachate is collected above the liner and removed for proper treatment and disposal. Leak detection and collection is implemented beneath the primary liner and above the secondary liner. Gas produced from aerobic and anaerobic decomposition is collected and safely used or disposed of. This gas is primarily carbon dioxide or methane but can include sulphurous compounds. Depending on the content of the gas, carbon dioxide can be vented directly to the atmosphere or collected, filtered, and used beneficially. Monitoring and documentation are maintained for the life of the landfill. Landfills with Limited Control Measures are landfill types that do not meet the description requirements specified in the Landfill with Significant Control Measures section. The permeability, leachate and gas control, and documentation are generally less restrictive. Leachate control may be non-existent or consist of simple collection and drain to local sewer lines. Gases may be vented versus stored, treated and used. Monitoring requirements for these types of landfills are less stringent – requiring less frequent sampling, inspections, and records for a shorter time depending on the local laws and regulations.

Source: Higg Index

Normalized data

Normalized data includes a comparison of totals or usage data against a predefined variable (or set of variables), e.g. kWh of electricity used per employee on-site, kg of hazardous waste per unit of production etc. An organization can decide whether absolute or normalized data are going to be the most appropriate and representative data to collate/report. Within each of the performance areas discussed in this document there are examples of variables against which data can be normalized.

Source: GSCP

Normalized reductions

Reduction in actual utility consumption (e.g. average kWh of electricity used, or cubic meter of water used per employee on-site within a calendar year)/pollution generated (e.g. average kg of hazardous waste per unit of production within a calendar year) that has been normalized to a business metric (e.g. units or mass of production, unit revenue, unit gross sales, unit turnover, full-time employee equivalent, square foot) when compared to normalized utility/pollution generated in a base year. To calculate a normalized value, measure utility/pollution generated in a given time period and divide by the chosen business metric. For example, a normalized waste generation can be calculated as follows: 10,000 kg waste ÷ 5,000 garments = 2kg waste/garment.

Off-site wastewater treatment

Off-site wastewater treatment is a third-party enterprise or organization who provides wastewater treatment service for more than two pollutant discharging entities by collecting their wastewater, and the wastewater discharged directly to the environment should meet with the relevant limits. The off-site treatment can be public wastewater treatment facility, regional wastewater treatment facility (i.e. industrial park, industry area etc.)

Source: Higg Index

Offsite incineration without energy recovery for Non-Recyclables

Incineration of non-recyclable wastes offsite at a third-party facility that does not recover energy from the incineration process.

Source: Higg Index

Offsite incineration without energy recovery for Recyclables

Incineration of recyclable wastes offsite at a third-party facility that does not recover energy from the incineration process.

Source: Higg Index

On-site wastewater treatment

On-site wastewater treatment is the wastewater treatment plant used and managed by the factory only. After being treated by the on-site treatment, the wastewater can meet with relevant limits and be directly discharged into the environment, or into an Off-site 3rd party treatment plant (known as partial onsite treatment).

Source: Higg Index

Onsite incineration without energy recovery for Non-Recyclables

Incineration of non-recyclable wastes onsite at the facility that does not recover energy from the incineration process

Source: Higg Index

Onsite Incineration without energy recovery for Recyclables

Incineration of recyclable wastes onsite at the facility that does not recover energy from the incineration process.

Source: Higg Index

Open burning

Open burning is outdoor burning of wastes such as lumber, scrapped cars, textiles, sawdust and so forth.

Source: OECD

Permit

Permit is defined as all documents required to comply and submit to the government, including but not limited to governmental permits, authorizations, licenses, registrations, certificates, annual government reports and registration of specific chemicals use.

Source: Higg Index

Personal protective equipment

Personal protective equipment, commonly referred to as “PPE”, is equipment worn to minimize exposure to hazards that cause serious workplace injuries and illnesses. These injuries and illnesses may result from contact with chemical, radiological, physical, electrical, mechanical, or other workplace hazards. Personal protective equipment may include items such as gloves, safety glasses and shoes, ear plugs or muffs, hard hats, respirators, or coveralls, vests and full body suits.

Source: US Department of labor

Point Source

Air flow which is actively controlled and directed (e.g., by fan and exhaust ducting) into the atmosphere from a single stationary fixed source such as stack or vent. Examples include boiler exhaust stack, the exhaust stack of a local ventilation system used to capture emissions from processes that emit volatile organic compounds (VOCs).

Source: Higg Index

Preventative maintenance

Preventative maintenance (or preventive maintenance) is maintenance that is regularly performed on a piece of equipment to lessen the likelihood of it failing. Preventative maintenance is performed while the equipment is still working, so that it does not break down unexpectedly.

Source: Fiix

Produced/process water

Water which, during extraction or processing, comes into direct contact with or results from the production or use of any raw material (e.g. crude oil or a by-product from sugar cane crushing), intermediate product, finished product, by-product, or waste product. Note this also includes reused / recycled water.

Source: CDP Water Reporting Guidance

Production Energy use

Energy that is directly or indirectly consumed in production related activities or production areas such as production equipment operations, onsite energy generations for production (e.g. steam or electricity), industrial wastewater treatment plant, production area lighting, heating, ventilation and cooling, etc.

Source: Higg Index

5. Words Q-T

Rainwater

If a company is managing rainwater, either to harvest and use, or to prevent flooding for example, they should try to estimate and disclose it as withdrawal from the hydrological system. This helps companies better understand their water dependency and risks.

Source: CDP Water Reporting Guidance

Rainwater Harvesting

Rainwater harvesting is the collection the run-off from a structure (e.g., roof) or other impervious surface in order to store it for later use.

Recycle

Requires the waste to be re-processed so as to obtain a product, material or substance whether for the original or other purposes. It does not include energy recovery and the reprocessing into materials that are to be used as fuels or for backfilling operation. For example: Plastic recycling is the process of recovering scrap or waste plastic and reprocessing the material into useful products, sometimes completely different in form from their original state. For instance, this could mean melting down soft drink bottles and then casting them as plastic chairs and tables. Plastic used for playground surfaces or traffic cones Padding/stuffing used for furniture, mattresses, blankets, toys

Source: Higg Index

Recycle waste(including Upcycle)

Pre or post-consumer wastes are reprocessed to produce new items of equal (or better) quality (e.g., textile to textile recycling or processing plastic bottles into fabric).

Source: Higg Index

Recycled Domestic Wastewater

Recycled domestic wastewater is defined as domestic wastewater that has been treated using physical, chemical, and/or any additional treatment processes to meet a quality which allows the water to be used again for domestic uses such as landscape irrigation, toilets.

Recycled Industrial Wastewater

Recycled industrial wastewater is defined as process wastewater that has been treated using physical, chemical, and/or any additional treatment processes to meet a quality which allows the water to be used again in a production process. For example, wastewater that has gone through a membrane filtration process and used back in the industrial operations is considered recycled water. This does not include water cycled in operations such as cooling towers and non-contact heat exchange operations or water that is recycled and used for domestic uses such as landscape irrigation.

Recycled Water

Recycled Process Water: treated effluent used again in main process Reused Water: treated effluent used in other areas except recycled water such as toilets or landscaping Recycled water is the reuse of wastewater that has been treated to remove solids and certain impurities to meet water quality standards associated with the designated application.

Souce: CDP Water Reporting Guidance

Renewable energy

This relates to energy generated by a renewable source (i.e. source which is not depleted or used up as it is naturally replenished. Renewable sources can either be managed so that they last forever, or so that their supply is not significantly impacted. Unlike fossil fuels, most renewable energy sources do not release carbon dioxide and other air pollutants as by-products into the atmosphere. As the amount of fossil fuel resources on Earth decreases, it is becoming increasingly important to find and utilize renewable energy sources. Examples include: solar, biofuels, wind, hydroelectric, geothermal, tidal and wave

Source: GSCP

Restricted Substance Lists (RSLs)

A list, compiled by a business, trade group or other organization, of chemicals (aka chemical substances) to be actively managed and informed on. An RSL may contain chemicals for controlled use, targeted for elimination/substitution, and those that may be totally banned or may be regulated. (e.g., American Apparel and Footwear Association (AAFA) RSL)

Source: OIA – Chemicals Management Framework Glossary

Reuse

Means checking, cleaning or repairing recovery operations, by which products or components of products that have become waste are prepared so that they can be re-used without any other preprocessing whether for the original or other purposes. For example: Chemical supplier can reuse the chemical container for filling them up with the same chemical. Fabric leftover can be reused in another factory. Rechargeable batteries can be reused many times

Source: Higg Index

Reuse waste

Pre or post-consumer wastes are reused to make new or second hand products without modification or additional manufacturing steps before using the waste

Source: Higg Index

Reuse water

Wastewater discharged from one process that is used directly in another process without treatment. This does not include water cycled in operations such as cooling towers and non-contact heat exchange operations.

Rubber material

A tough, flexible, highly resilient, waterproof material. Natural rubber is produced using an organic compound (isoprene) usually harvested in the form of latex from rubber trees. A synthetic rubber is any artificial elastomer (polymer with elastic properties).

Safety Data Sheets (SDS)

SDS (also called material safety data sheet (MSDS) or production safety data sheet (PSDS)) is an important component of product stewardship and occupational safety and health. It is intended to provide workers and emergency personnel with procedures for handling or working with a substance in a safe manner and should include information such as physical data (melting point, boiling point, flash point, etc.), toxicity, health effects, first aid, reactivity, storage, disposal, protective equipment, and spill-handling procedures.

Source: Higg Index

Science Based Targets Initiative (SBTi)

The Science Based Targets Initiative (SBTi). has established procedures for the commitment, submission, validation, and approval of targets, which generally includes: – Company commitment to setting Science-Based Targets in line with the SBTi. Formal commitment to the SBTi is required (i.e., submitting the commitment letter and paying the applicable fees) – Setting your company’s GHG target and having it validated and approved by the SBTi.

Source: Higg Index

Scope 1 emissions

Direct GHG emissions occur from sources that are owned or controlled by the company, for example, emissions from combustion in owned or controlled boilers, furnaces, vehicles, etc.; emissions from chemical production in owned or controlled process equipment.GHG protocol

Scope 2 emissions

Scope 2 accounts for GHG emissions from the generation of purchased electricity consumed by the company. Purchased electricity is defined as electricity that is purchased or otherwise brought into the organizational boundary of the company. Scope 2 emissions physically occur at the facility where electricity is generated.

Source: GHG protocol

Scope 3 emissions

All other indirect GHG emissions that occur as a result of an organization’s activities but are not classified as scope 1 or scope 2 emissions. Scope 3 emissions are typically associated with activities and sources that are behind a company’s immediate control or ownership but are part of its value chain.

Source: GHG protocol

Septic System

Septic systems are underground wastewater treatment structures that use a combination of natural/primary processes to treat wastewater. The process typically involves solids settling within the septic tank and ends with wastewater being discharged to the soil via a drainfield.

Source: Higg Index

Stakeholders

Stakeholders are defined broadly as those groups or individuals: (a) that can reasonably be expected to be significantly affected by the organization’s activities, products, and/or services; or (b) whose actions can reasonably be expected to affect the ability of the organization to successfully implement its strategies and achieve its objectives.

Source: GRI G3 2001

Standard Allowed Minute (SAM) or Standard Minute Value (SMV)Standard Minute Value, or SMV,

SMV is the time value arrived at for a task based on the average rate of output which qualified workers will naturally achieve without over exertion provided that they know and adhere to the specified method and provided that they are motivated to apply themselves to their work. (ILO) Note that SMV is often used interchangeably with Standard Allowed Minute, or SAM.

Source: International Labour OrganizationIntroduction to Work Study, 4th ed.

Stormwater

Water that originates from precipitation (e.g., rainwater) that accumulates on and runs off roofs, hard standing surfaces, car parks, etc. (sometimes referred to as surface water run‐off)

Source: Higg Index

Subcontractor

A separate business entity used to perform a specific process or manufacturing step to produce a final product such as garment dyeing, embroidery, and screen-printing tasks, etc.

Source: Higg Index

Synthetic leather materials

A synthetic (man-made and typically petroleum-based) material used as a substitute for leather.

Target

A formal target here refers to a quantified performance requirement of the site’s annual utility use of a particular utility source. A formal target must: 1) include a definite start date (i.e., “baseline”) of target, the measurement unit, and the baseline consumption (i.e. m3/year at 2010 baseline) 2) include an end date of the target, meaning the intended completion of the required reductions; and 3) include an exact reduction quantity, expressed as a number (e.g. reduce by 1 million m3) or a percentage (e.g. reduce by 5%). 4) be relevant to reducing the site’s utility use (e.g. focuses on the most significant utility uses at the site)

Source: Higg Index

Total suspended solids (TSS)A measure of the suspended solids in wastewater, effluent, or water bodies, determined by tests for “total suspended non-filterable solids”.

Source: OECD

Treated Wastewater from External Source

Wastewater that has been discharged and treated by an external source (e.g., other manufacturing facility) using physical, chemical, and/or any additional treatment processes to meet a quality which allows the water to be used again in a process.

6. Words U-Z

Units

Units refer to common consistent units. Examples: If dyeing or using wet processes proper units would be volume/mass. For finished goods, proper units are volume/piece.

Source: Higg Index

Untreated Wastewater from External Sources (treated internally)

Wastewater that has been discharged by an external source (e.g., other manufacturing facility) and treated at your facility using physical, chemical, and/or any additional treatment processes to meet a quality which allows the water to be used again in a process.

Upcycling

Upcycling is the process of transforming by-products, waste materials, useless and/or unwanted products into new materials or products of better quality or for better environmental value

Source: Higg Index

Upstream Scope 3 Emission Sources

1. Purchased goods and services

2. Capital goods

3. Fuel- and energy-related activities (Not included in scope 1 or scope 2)

4. Upstream transportation and distribution

5. Waste generated in operations

6. Business travel

7. Employee commuting

8. Upstream leased assets

Source: GHG protocol

Verification – Onsite

When an Cascale approved verifier conducts a verification by entering onto the manufacturer premises and completes the verification in person.